Firmware: 
1. O2 Feedback: 
Add option O2FB_Minimum_RPM.\~ Engine speed must be above this value and below existing option O2FB_Maximum_RPM for feedback to be active.
2. NOS Fuel Map control range: 
+/- 50% is not adequate range for NOS Fuel map.\~ - 50% to +300% would be ideal.\~ 
-100 TO +300% 
3. Accel Fuel Trim vs Coolant Temp
Add 2D table vs coolant temp.\~ 0% to +100% range.\~ 0% is no trim. 
4. Alt Function Vehicle Speed Threshold: 
Add option Alt_OK_Below_VSS.\~ If vehicle speed value greater than this value, disable Alt function. 
5. AEM Data Stream: 
6. Ignition Fixed option: 
If option Ignition_Fixed = ON then ignition timing forced to a value defined by the option Ign_Fixed.\~ All individual cylinder trims must be disabled in this mode.\~ The result must be displayed in the parameter Ign Timing.\~
The intent has always been to update the Configure ECU | Set Ignition wizard in AEM Pro so the user can force a constant ignition timing regardless of any trims while syncing.\~ This won\rquote t work if the parameter Ign_Timing doesn\rquote t match.
7. Ignition Difference Map: 
This map should be modified to allow only negative values to be entered. 
8. Crank Injector Time table: 
Multiply Y-axis raw values by option MicroSec/bit and display these values instead of raw numbers in the table. 
9. INCREASE RANGE ON MXTIME FOR HIGH COMPRESSION ENGINES 16:1
IF MISSING=+1 d_Tooth_Time = Tooth_Time (1+MXTIME)
IF MISSING=+2 d_Tooth_Time = (Tooth_Time (1+MXTIME))*2
10. 8BIT O2 FB inhibits Added O2 FB Cut inhibit for when limiters active
 
AEM Pro: 
UNTRACKED - Expanded configure outputs dialog for AEM by adding a third section 
titled Switched Output Configure. 
UNTRACKED - Added fixed timing to the ignition setup window programming the 
options ignition fixed and ign fixed. 
UNTRACKED - Added shortcut button to menu bar for context window 
UNTRACKED - Added connect to ECU or work offline dialog box on start up of AEM 
Pro 
UNTRACKED - Fixed problem where closing a file by disconnect following an 
attempt to change a calibration online while the ECU is offline resulted in 
a GPF 
UNTRACKED - Added shortcut button for configure outputs to AEMPro 
UNTRACKED - Added message dialog following closure of injector change function 
window to open the battery offset wizard if desired. 
UNTRACKED - Added AEM log icon in AEMPro. Also added ability to open a log 
file in AEMLog following successful download of a log file. 
UNTRACKED - Fixed bug whereby editing menus resulted in the parameter list 
combo in gcom used for comms code options having an extra full list added. 
GA89010832 - Fixed bug where the set value function of a map in tabular view 
fails. 
GA89010829 - Added support for 'comms code' options. This allows the user to 
see and/or modify such an option using a pull down list box showing the 
names of 
the parameters. 
GA89010818 - Modifications made to x axis of tabular maps such that the angle 
of text changes to better utilise the available space according to the shape of 
the rectangle in which it fits. It also uses a bigger maximum size font. 
GA89010822 - Fixed bug where printing full option list may throw an exception. 
The sizing has also be changed to allow for the extra possible length of 
options 
(20 characters as opposed to designed 12) and for option string list entry 
space (e.g. A/C Request Input = Switch is always OFF) 
GA89010361 - Added notes indicating fuel pressure/injector throughput changes 
when effected. 
GA89010778 - Added ability to specify ECU name and version sub-directories off 
the default calibration directory into which to store calibrations. 
Non-AEM only. 
UNTRACKED - Fixed bug in batch import GDFs throwing abnormal termination. 
GA89010833 - Modifications made to ini.h to set programmable parameters' 
modification methods appropriately (which use new modifiers) for older ini 
versions. This provides complete compatibility with old and new ini files that 
use new modifiers. 
GA89010744 - Added separators to custom menu editor 
GA89010782 - Added message on import templates to indicate if no template 
was found. Import templates does work correctly. 
GA89010826 - Prevent downloading of log data when connected to an ECU that does 
not support it and indicate the ECU does not support it when otherwise 
appropriate (not connected and selected ECU | Download log data...) 
GA89010772 - Fixed bug where resizing a table window resulted in the obscuring 
of the active site under follow ECU. 
GA89010573 - Fixed bug under full option window where hexadecimal values did 
not work. 
UNTRACKED - Fixed bug whereby dongle detect wasn't working. 
UNTRACKED - Fixed bug whereby comparing calibrations across different ECUs 
rarely resulted in nothing apparently happening (actually crashing). 
UNTRACKED - Fixed bug whereby crashes repeat if a table graph window is
displayed when the associated tabular view is not shown. Only noticeable if the
current table site value changes.

GA89010857 - Alpha sorting of menu view for unconfigured menus.

GA89010854 - Added support for 'f' key in full option list enabling selection of
the search list box and allowing the entry of the 'f' character for hexadecimal
options.

GA89010858 - Modified menu editor to enable delete button between the menu view
and available items all the time.

GA89010859 - Modified menu editor to default to 'Options' and 'Parameters' as
the names for option and parameter menus. Previously this was the case, but upon
reopening the editor the names were 'Option' and 'Parameter'.

GA89010734 - Allow hexadecimal values to be entered into the table sites in a
tabular view of a hexadecimal table.

GA89010865 - Removed 'template save as window' from menu as no longer wanted or
required.

GA89010863 - Added ability for custom menus to be temporarily disabled. Only
applicable to GWv3.

GA89010864 - Removed modification of GIN directory on install of another GIN
file. This provides a fixed install directory as defined in the installation.
This modification allows for GIN files to be installed from any directory and
auto-convert templates to remain in and run from the default GIN directory.

UNTRACKED - Fixed bug noticed in FuelOPWindow whereby changing between various
mutually exclusive options appeared to work on screen but actually failed in
the ECU. The reasoning is as follows. The commands to change the options were
effected one at a time with a WaitForECUCommands call between each. This checked
that the comms library had finished processing all commands before processing
the next option command (e.g. turn off O2 FB1, turn on O2 FB2). However, the
application may not have carried out the changes to the map internally, that is,
it may not have processed the comms queue locally to effect the changes to the
inimap.

GA89010868 - Problem with secureable ECUs whereby if upload a secured
calibration to an ECU and cycle power, comms continues but fails. This should
result in comms failure and a secured ECU. GW should operate as per a connected
ECU when power is cycled which does result in comms failure. The reason for this
is that on upload the comms library is not notified of either COMOK or the log
buffer. By notifying the library of these events, GW operates as expected.

GA89010873 - Enabled context sensitive help at start up for all projects other
than AEMPro when a check for the existence of GWLink.hlp succeeds.

UNTRACKED - Bug fix in redraw.cpp whereby loading the option user scalars always
used IM instead of the passed ini map.

GA89010837 - Modified manual conversion such that on conversion from a
non-secure ECU to a secure ECU the password is set to 0xff.

GA89010850 - Under compare across different versions, copying a value into the
current calibration failed to remove the entry from the list. This occurred
because the converted value isn't exactly the same. Modifications made ensure
the entry is removed as the conversion is as close as possible.

UNTRACKED - Mods to provide descriptive labels for automatic conversion
templates.

UNTRACKED - Mods to ensure both GIN files are installed for a conversion
template.

GA89010838 - Mods to open notes dialog (as used by file | open) such that the
user-specified directory structure for calibration files is appropriately
navigated when the calibration filter is changed.

GA89010839 - Mods to compare open dialog to use the currently selected ECU
filter to navigate to the appropriate directory.

UNTRACKED - Mods to ConvFrontWnd such that individual table/map site values can
be set by an automatic conversion template.